Intelligent Manufacturing and Energy Sustainability

Alignmentfor Hybrid Additive Manufacturing using Computer Vision.- Development of a colour and orientation detection system for small part feeding.- Comparative analysis on battery used in Solar Refrigerated E-rickshaw in India.- "Application of Value Stream Mapping (VSM) in a Sewing Line for Improving Overall Equipment Effectiveness (OEE): A Case Study".- CFD analysis to increase heat transfer in pipe with combined effect of circular perforated ring and twisted tape insert.- Study On Solar Parabolic Trough Collector With Different Copper Absorber Tubes.- Harmonic Analysis for Bidirectional Grid Connected Converter for Electrical Vehicle during Charging and Discharging Operations.- Effect of tribolayer on the sliding wear behavior of detonation sprayed Alumina-Titania coatings.- Development of Sustainable Cementitious Binder Utilizing Silicomanganese Fumes.- Review on Sliding wear of Ti6Al4V alloy concerning counterface and sliding conditions.- Hardness and Microstructure studies on the effect of Solution treated-age hardened Al-6082 Alloy.- Floating Photo Voltaic Thin Film Technology - A Review.- Effect of Ethanol fumigation on performance and combustion characteristics of Compression Ignition Engine fuelled with Used Cooking Oil Methyl Ester in dual fuel mode.- Estimation and Moderation of Harmonics in Distribution Systems.- Theoretical Evaluation of Energy Performance of a Vapour Compression Refrigeration System Using Sustainable Refrigerants.- Effect of Autofrettage on the properties of the Aluminum Cylinders.- Influence of Graphene and Tungsten Carbide Reinforcement on Tensile and Flexural strength of Glass Fiber Epoxy Composites.- Investigation of partial discharge due to copper spherical particle in power transformer under various oil flow models using CFD.- A high power high frequency isolated DC-power supply for electrical vehicle charging application.- Effect of Slicingthickness and Increment on the design of patient specific implant for Total Knee Replacement (TKR) using Magnetic Resonance Imaging (MRI) - A case study.- Microstructure and Hardness Behavior Sudy of Carbon Nanotube in Aluminium Nanocomposites.- Comparison of Electric field with and without corona ring for 66kV line insulator.- Experimental and FEA Simulation of Thermal-Fluid Interaction Between TIN Coated Tungsten Carbide Tool and Inconel-825 Workpiece.- The Effect of Recrystallization on Electrical Resistivity of Stir Casted SiCP/AA6061 Composite after Shot Peening.- Static Stress Analysis of WYE-Piece for penstock application.- Comparative Investigation on Gas Tungsten Arc Welding and Friction Stir Welding of Electrolytic Tough Pitch Copper Plates.- Synthesis and Characterisation of Functionally Graded Ceramic Material for Aerospace Applications.- CI Engine Characteristic Investigation by Application of Metal Based Additives with Biodiesel Blends.- Simulation of underground cable faults (defects) with the detection of partial discharge.- Comparison of CI Engine performance parameters and Emissions by varying designs of Intake Manifolds.- Variation of Time Lag, Decrement Factor and Inside Surface Temperature with Solar Optical Properties of Building Envelope in Different Climatic Zones of India.- Study On Tensile and Hardness Properties of Al7075 Alloy Reinforced With Graphite, Mica and E-Glass.- ANN based fault classification and section identification technique using superimposed currents for three-terminal transmission line.- An analytical investigation for combined pressure driven and electroosmotic flow without the Debye-Huckel approximation.- Addressing the Green tribology advancement, future development and challenges.- Effect of Drying Temperature to the Drying Characteristic, Morphology and Peak Viscosity of Traditionally Processed Sago Starch (Lemantak).- Evaluating Mechanical Properties of Egg Shell and Coco Peat Reinforced Epoxy Composite.- Design Modification of Rear Axle Housing by Fatigue Failure Analysis.- Mixture Design using Low Cost Adsorbent Materials for Decolourisation of Biomethanated Distillery Spent Wash in Continuous Packed Bed Column.- Prediction of the WPPO Biodiesel Fuelled HCCI Engine Using Artificial Neural Networks.- Dimensional Analysis of Form Drilling parameters by Buckingham pi theorem and optimization of heat generation in Form drilling process by Taguchi.- Comparison of ductile, flexural, impact and hardness attributes of sisal fiber reinforced polyester composites.- Optimization of EDM Process Parameters using Standard Deviation and Multi-Objective Optimization on the basis of Simple Ratio Analysis (MOOSRA).- Modeling and Simulation of Trans Z-source Inverter with Maximum Constant Boost PWM Control for Solar PV System.- Driver Drowsiness Monitoring System.- Detection and Controlof Water Leakage in Pipelines and Taps Using Arduino Nano Microcontroller.- Smart Automated Processes for Bottle-filling Industry using PLC-SCADA System.- Effect of Stirring Speed During Casting on Mechanical Properties of Al-Si Based MMCs.- Exploration of Pillars of Industry 4.0 using Latent Semantic Analysis Technique.- An Overview of Different Topologies of DC-DC Bidirectional Converter for Different Applications.- An Approach to detect and classify defects in Cantilever Beams using Dynamic Mode Decomposition and Machine Learning.- Musculoskeletal Simulation and Analysis of Upper Limb Rehabilitation Device.- Fuzzy Regenerative Braking Strategy.- A New Framework for Secure utsourcing of Medical Data.- A Comprehensive View for Providing the Decision on Medicare data.- Predicting Cardiac-Arrhythmia Using QRS Detection and Multi-Layer Perceptron.- Full Length Driver Drowsiness Detection Model - Utilising Driver Specific Judging Parameters.- Enterprise Reporting Solution on Integrating Business Intelligence for  Operational and Financial Data.-  Accelerating The Classifier Training Using Various Boosting Schemes Within Cascades Of Boosted Ensembles (Cobes).- Service Layer Security Architecture For Iot Using Biometric Authentication And Cryptography Technique.

Australia-India Research Centre for Automation Software Engineering (AIRCAUSE). AICAUSE is a joint initiative of RMIT University, State Government of Victoria and ABB Group (India and Australia). He completed his B.E., M.E. and Ph.D. from RMIT University Melbourne, Australia. He has published over 125 peer-reviewed publications, with 493 citations in the last 5 years. He has developed fast 3D metal printing technology, won an international award in Germany. For his contributions, Dr Simic has also received other prestigious awards and recognitions: Two for the research and development from Honeywell and two RMIT University awards for excellence in teaching and the provision of education to the community. As a KES Journal General Editor, Dr Simic is processing around 400 papers per year, with the support of more than 70 Associate Editors and 600 reviewers. KES is a worldwide association involving about 5000 professionals, engineers, academics, students and managers.

Dr. Margarita N. Favorskaya is a Professor and Head of Department of Informatics and Computer Techniques at Siberian State Aerospace University, Russian Federation. Professor Favorskaya is a member of KES organization since 2010, the IPC member and the Chair of invited sessions of international conferences. She serves as a reviewer in international journals (Neurocomputing, Knowledge Engineering and Soft Data Paradigms, Pattern Recognition Letters, Engineering Applications of Artificial Intelligence), an associate editor of Intelligent Decision Technologies Journal and Computer and Information Science Journal. She is the author or the co-author of 160 publications and 20 educational manuals in computer science. She co-edited 5 books for Springer recently. She has supervised 8 PhD candidates and presently supervising 5 PhD students. Her main research interests are a digital image and video processing, remote sensing, pattern recognition, fractal image processing, artificial intelligence, information technolog